150 RPM to Radians Per Second Converter
Instant conversion for 150 RPM to rad/s (15.707963 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 15.707963
- Degrees per Second (°/s)
- 900 °/s
- Hertz (Hz)
- 2.5 Hz
- Revolutions per Second (RPS)
- 2.5 rev/s
- Revolutions per Hour (RPH)
- 9,000 rev/hr
- Revolutions per Day
- 216,000 rev/day
- Radians per Minute (rad/min)
- 942.4778 rad/min
- Milliradians per Second (mrad/s)
- 15,707.963 mrad/s
- Period (seconds per rev)
- 0.4 s/rev
- Exact Formula
- 150 × π/30 = 15.707963 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 150 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 150 × (π / 30) = 15.707963 rad/s
Exact fraction: 150π/30 rad/s · Reciprocal: 15.708 rad/s × (30/π) = 150 RPM
Reverse Conversion: 15.708 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
150 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
150 RPM = 5π rad/s ≈ 15.707963 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 15.705 rad/s instead of the exact 15.708 rad/s — an error of 0.002963 rad/s.
What this speed looks like in practice
At 150 RPM a shaft turns about 3.33× as fast as a 7-inch single (45 RPM). A ceiling fan on high turns about 1.33× faster.
Revolutions over time
That is 9,000 revolutions per hour and 216,000 per day. A quarter turn (90°) takes 100 ms, and the shaft sweeps 0.9° every millisecond.
Rim speed and centripetal load at ω = 15.708 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.1571 m/s · 0.5655 km/h | 2.467 m/s² · 0.2516 g |
| 5 cm | 10 cm | 0.7854 m/s · 2.827 km/h | 12.34 m/s² · 1.258 g |
| 10 cm | 20 cm | 1.571 m/s · 5.655 km/h | 24.67 m/s² · 2.516 g |
| 25 cm | 50 cm | 3.927 m/s · 14.14 km/h | 61.69 m/s² · 6.29 g |
| 50 cm | 1 m | 7.854 m/s · 28.27 km/h | 123.4 m/s² · 12.58 g |
| 1 m | 2 m | 15.71 m/s · 56.55 km/h | 246.7 m/s² · 25.16 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 150 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 2.5 Hz | Below typical VFD range — use a gearbox |
| 4 | 5 Hz | Reachable with a VFD |
| 6 | 7.5 Hz | Reachable with a VFD |
| 8 | 10 Hz | Reachable with a VFD |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 50 RPM · 5.236 rad/s | ×3 |
| 5:1 | 30 RPM · 3.142 rad/s | ×5 |
| 10:1 | 15 RPM · 1.571 rad/s | ×10 |
| 30:1 | 5 RPM · 0.5236 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.1234 J |
| 0.01 kg·m² (bench-grinder wheel) | 1.234 J |
| 0.1 kg·m² (car flywheel) | 12.34 J |
| 1 kg·m² (industrial flywheel) | 123.4 J |
Multiples of this speed

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 150 RPM to radians per second, multiply 150 by π and divide by 30: 150 × (π / 30) = 15.707963 rad/s (approx. 15.708 rad/s).
150 RPM equals 2.5000 Hz (revolutions per second), calculated by dividing 150 by 60 seconds.
To convert 15.708 rad/s back to RPM, multiply by 30 and divide by π: 15.708 × (30 / π) ≈ 150 RPM.
At 150 RPM, one full 360° revolution takes 0.4 seconds (400.00 ms).
A 4-pole induction motor has a synchronous speed of 150 RPM at 5 Hz (f = RPM × poles / 120 = 150 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 15.707963 rad/s × 0.1 m = 1.5708 m/s (5.6549 km/h). The centripetal acceleration at the rim is ω²·r = 24.674 m/s².