RPM to Hz Calculator
Type in any box: RPM, hertz, rad/s, degrees per second or period. The others update as you type. Add a pole count to see the electrical frequency of a motor or generator at that speed.
RPM · Hz · rad/s · °/s · period
Edit any field; the rest follow. Commas and dots both work as decimals.
RPM to Hz formula
RPM counts revolutions per minute and hertz counts cycles per second. One full revolution is one cycle, so the only difference is minutes versus seconds:
f [Hz] = n [RPM] / 60n [RPM] = 60 × f [Hz]ω [rad/s] = 2π × f = n × π / 30T [s] = 1 / f = 60 / nf_e = P × n / 120The last line matters for AC machines. A motor with P poles has P/2 pole pairs, and the magnetic field completes one electrical cycle for every pole pair that passes. So a 4-pole machine's electrical frequency is twice its mechanical frequency. That is why a 4-pole motor on 50 Hz runs near 1500 RPM, not 3000. For the full picture, including slip, use the motor slip calculator.
To go from frequency to angular velocity, multiply by 2π. If you only need RPM ↔ rad/s, the main converter does that with working shown.
RPM to Hz conversion table
| RPM | Hz | rad/s | Period |
|---|---|---|---|
| 1 | 0.016 67 | 0.1047 | 60 s |
| 60 | 1 | 6.283 | 1 s |
| 600 | 10 | 62.83 | 100 ms |
| 750 | 12.5 | 78.54 | 80 ms |
| 1000 | 16.67 | 104.7 | 60 ms |
| 1200 | 20 | 125.7 | 50 ms |
| 1500 | 25 | 157.1 | 40 ms |
| 1800 | 30 | 188.5 | 33.3 ms |
| 3000 | 50 | 314.2 | 20 ms |
| 3600 | 60 | 377.0 | 16.7 ms |
| 6000 | 100 | 628.3 | 10 ms |
| 10 000 | 166.7 | 1047 | 6 ms |
Motor and generator frequency by pole count
Synchronous speed n_s = 120 × f / P. Induction motors run a few percent below these figures because of slip; synchronous machines and alternators run exactly on them.
| Poles | 50 Hz | 60 Hz | Mech. Hz at 50 / 60 |
|---|---|---|---|
| 2 | 3000 | 3600 | 50 / 60 |
| 4 | 1500 | 1800 | 25 / 30 |
| 6 | 1000 | 1200 | 16.7 / 20 |
| 8 | 750 | 900 | 12.5 / 15 |
| 10 | 600 | 720 | 10 / 12 |
| 12 | 500 | 600 | 8.33 / 10 |
On a variable-frequency drive the same formula holds at any output frequency: a 4-pole motor at 40 Hz turns at about 1200 RPM. More in VFD frequency to RPM.
Where RPM ↔ Hz comes up
- Vibration analysis: a shaft running at 1800 RPM puts its 1× peak at 30 Hz, 2× at 60 Hz. Bearing and blade-pass frequencies are multiples of shaft Hz.
- Tachometers and encoders: pulse frequency ÷ pulses per revolution × 60 gives RPM.
- Stroboscopes: the flash rate in Hz × 60 freezes a shaft at that RPM (see stepper motor steps to RPM for pulse-based drives).
- Audio and turntables: 33⅓ RPM is 0.556 Hz; 45 RPM is 0.75 Hz.
- Generators: frequency output from engine speed and pole count.
Common mistakes
- Confusing Hz with rad/s. Both are "per second", but 1 Hz is 2π rad/s. Mixing them gives errors of 6.28×.
- Assuming motor speed = 60 × supply Hz. That is only true for 2-pole machines. Divide by pole pairs.
- Reading rotor speed off a vibration spectrum's biggest peak. The largest peak is often 2× running speed or a blade-pass frequency.
Frequently asked questions
How do you convert RPM to Hz?
Divide RPM by 60. 1800 RPM ÷ 60 = 30 Hz.
How do you convert Hz to RPM?
Multiply hertz by 60. 50 Hz × 60 = 3000 RPM.
Is 1 Hz equal to 60 RPM?
Yes. One hertz is one cycle per second, and one revolution per second is 60 revolutions per minute.
Why does a 4-pole motor on 60 Hz run at 1800 RPM, not 3600?
Because synchronous speed is 120 × f / P. With four poles there are two pole pairs, so the field rotates once for every two electrical cycles: 120 × 60 / 4 = 1800 RPM.
How do I convert Hz to rad/s?
Multiply by 2π. 60 Hz × 2π = 376.99 rad/s.
What is the period of 3000 RPM?
3000 RPM = 50 Hz, so one revolution takes 1/50 s = 20 ms.
Terms used on this page
- RPM (min⁻¹)
- Revolutions per minute; mechanical rotation speed.
- Hertz (Hz)
- SI unit of frequency, one cycle per second.
- Angular frequency (ω)
- 2π × frequency, in rad/s.
- Period (T)
- Time for one complete revolution or cycle, 1/f.
- Pole pair
- One north and one south magnetic pole; a P-pole machine has P/2 pairs.
- Synchronous speed
- Speed of the rotating magnetic field, 120·f/P RPM.
Related calculators
- Torque, Power & RPM CalculatorSolve P = τ·ω for power, torque or speed in kW, hp, N·m and lb·ft.
- Gear Ratio & Pulley RPM CalculatorOutput RPM, torque and direction for gear trains and belt drives.
- SFM to RPM CalculatorSpindle RPM from cutting speed and diameter, plus feed rate.
- Linear ↔ Angular Velocity CalculatorConvert RPM and radius to m/s, km/h, mph and ft/min — and back.
- RPM ↔ rad/s converterω = n × π/30
- Motor slip calculatornₛ = 120·f / P