Gear Ratio and Pulley RPM Calculator
Enter the input speed and the driver and driven sizes for each stage, either tooth counts or pulley diameters. You get the overall ratio, output RPM and rad/s, output torque after friction losses, rotation direction and belt speed.
Gear train & belt drive
Add up to five stages. Torque and efficiency are optional.
Show the working
i1 = 60 / 20 = 3i = 3 = 3n_out = 1,750 / 3 = 583.333 RPMT_out = 20 × 3 × 0.98^1 = 58.8 N·m
Gear ratio formulas
A gear pair or pulley pair transmits motion at the pitch line, where both members move at the same surface speed. Equal surface speed means the larger member turns slower in proportion to its size. That gives four equivalent ways to write the ratio:
i = z_driven / z_driver = d_driven / d_drivern_out = n_in / iT_out = T_in × i × ηi_total = i₁ × i₂ × … × iₖHere z is the number of teeth, d the pitch diameter, n speed in RPM, T torque and η the mechanical efficiency of each stage (about 0.98 for a good spur or helical mesh, 0.95–0.97 for a V-belt, and as low as 0.5–0.9 for worm gears). The calculator applies η once per stage.
Ratios are dimensionless, so you can use any consistent unit for the diameters. Belt speed needs a real length, which is why the calculator assumes mm for that one output. For converting the output speed into rad/s, the formula is the usual ω = n × π/30 (see the RPM to rad/s converter).
Worked examples
- Single reduction. A 1750 RPM motor drives a 20-tooth pinion meshing with a 60-tooth gear. i = 60/20 = 3. n_out = 1750/3 = 583.3 RPM (61.09 rad/s). With 20 N·m in and 98% efficiency, T_out = 20 × 3 × 0.98 = 58.8 N·m.
- Two-stage gearbox. Stage 1 is 12:48 (4:1), stage 2 is 15:45 (3:1). i = 4 × 3 = 12. A 1450 RPM input gives 120.8 RPM out, turning in the same direction because there are two external meshes.
- V-belt drive. A 100 mm motor pulley at 1450 RPM drives a 250 mm pulley. i = 2.5, n_out = 580 RPM. Belt speed = π × 0.100 m × 1450 / 60 = 7.59 m/s, comfortably inside the 5–30 m/s band most V-belts are rated for.
- Picking a ratio. You need about 240 RPM from a 1750 RPM motor. i = 1750/240 = 7.3. A single stage that large is bulky, so split it: 2.5 × 2.92 ≈ 7.3, or use a 15:44 and 16:40 pair.
Output speed for common ratios
| Ratio | 1450 RPM in | 1750 RPM in | 2900 RPM in | 3500 RPM in |
|---|---|---|---|---|
| 1.5 : 1 | 966.7 | 1166.7 | 1933.3 | 2333.3 |
| 2 : 1 | 725 | 875 | 1450 | 1750 |
| 3 : 1 | 483.3 | 583.3 | 966.7 | 1166.7 |
| 5 : 1 | 290 | 350 | 580 | 700 |
| 10 : 1 | 145 | 175 | 290 | 350 |
| 15 : 1 | 96.7 | 116.7 | 193.3 | 233.3 |
| 20 : 1 | 72.5 | 87.5 | 145 | 175 |
| 30 : 1 | 48.3 | 58.3 | 96.7 | 116.7 |
| 50 : 1 | 29 | 35 | 58 | 70 |
Rotation direction and idler gears
Two external spur gears turn in opposite directions. Each additional external mesh flips direction again, so an odd number of meshes reverses the output and an even number keeps it. An idler gear placed between driver and driven adds a mesh (and reverses direction) without changing the ratio, because its tooth count cancels out.
Internal (ring) gears, belts and chains do not reverse direction. Planetary sets depend on which member is held. The calculator's direction readout assumes simple external meshes in gear mode and same-direction drives in pulley mode.
Common mistakes
- Swapping driver and driven. The ratio is always driven over driver. Swapping them turns a reduction into an overdrive.
- Adding stage ratios instead of multiplying. 3:1 followed by 4:1 is 12:1, not 7:1.
- Using outside diameter for pulleys. V-belts ride on the pitch diameter, which is smaller than the outside diameter. Using OD can put you 3–8% off.
- Forgetting efficiency on torque. Speed ratio is exact; torque ratio is not. A three-stage helical box at 98% per stage delivers 94% of the ideal torque.
- Ignoring the motor's slip. A "1800 RPM" motor really turns at about 1750 RPM loaded. Use the nameplate figure, or check it with the motor slip calculator.
Frequently asked questions
How do you calculate gear ratio?
Divide the number of teeth on the driven gear by the number on the driving gear. 60 driven teeth and 20 driving teeth give a ratio of 3:1.
How do you calculate output RPM from gear ratio?
Output RPM = input RPM ÷ gear ratio. A 1450 RPM motor through a 5:1 reducer turns the output at 290 RPM.
Does a higher gear ratio mean more torque?
Yes. Output torque is input torque times the ratio times efficiency, so a 5:1 reducer gives roughly five times the torque at one-fifth of the speed.
How do I calculate pulley RPM?
Driven RPM = driver RPM × driver diameter ÷ driven diameter. A 100 mm pulley at 1450 RPM driving a 200 mm pulley gives 725 RPM.
What is the ratio of a multi-stage gearbox?
Multiply the individual stage ratios. 4:1 × 3:1 × 2:1 = 24:1.
Does an idler gear change the ratio?
No. An idler only changes the rotation direction and the spacing between shafts. Its tooth count cancels out of the ratio.
Terms used on this page
- Driver (pinion)
- The gear or pulley on the input shaft that supplies motion.
- Driven gear
- The gear or pulley on the output shaft that receives motion.
- Gear ratio (i)
- Driven size over driver size; above 1 is a reduction, below 1 an overdrive.
- Pitch diameter
- Diameter of the circle where meshing teeth or the belt's neutral line actually make contact.
- Idler
- A gear between driver and driven that reverses direction without changing the ratio.
- Mechanical efficiency (η)
- Output power ÷ input power for a stage; losses come from friction and churning.
Related calculators
- Torque, Power & RPM CalculatorSolve P = τ·ω for power, torque or speed in kW, hp, N·m and lb·ft.
- SFM to RPM CalculatorSpindle RPM from cutting speed and diameter, plus feed rate.
- Linear ↔ Angular Velocity CalculatorConvert RPM and radius to m/s, km/h, mph and ft/min — and back.
- RPM to Hz CalculatorRPM, Hz, rad/s, °/s and period in one live converter.
- RPM ↔ rad/s converterω = n × π/30
- Motor slip calculatornₛ = 120·f / P