Torque, Power and RPM Calculator
Enter any two of torque, power and shaft speed to get the third. Everything follows from one equation, P = τ × ω, with ω in rad/s. The calculator converts between kW, hp, PS, N·m, lb·ft and lb·in and shows every step.
Torque · Power · Speed
Choose what to solve for, then enter the other two values in any unit.
Show the working
ω = n × π/30 = 5,252 × π/30 = 549.988 rad/sP = τ × ω = 406.745 N·m × 549.988 rad/s = 223,705 W= 223.705 kW = 299.994 hp = 300 lb·ft
The torque–power–speed formula
Rotational power is the rate at which torque does work. One newton-metre of torque turning through one radian does one joule of work, so one N·m at one rad/s is one watt. That gives the exact SI relationship:
P = τ × ωω = n × 2π / 60 = n × π / 30P [kW] = T [N·m] × n [RPM] / 9549P [hp] = T [lb·ft] × n [RPM] / 5252The two shop constants come straight from that equation. 9549 is 60 000 / 2π, which absorbs the RPM-to-rad/s step and the watts-to-kilowatts step. 5252 is 33 000 / 2π: one horsepower is defined as 33 000 ft·lbf per minute, and 2π converts revolutions to radians. Neither number is empirical, and neither depends on the motor.
If your speed is already in rad/s, use the first line directly. If you need the RPM ↔ rad/s step on its own, the RPM to rad/s converter shows it with the exact π/30 factor.
Worked examples
- Motor nameplate torque. A 7.5 kW, 4-pole motor runs at 1450 RPM on 50 Hz. T = 9549 × 7.5 / 1450 = 49.4 N·m. In lb·ft that is 49.4 / 1.3558 = 36.4 lb·ft.
- Engine power from a dyno torque reading. An engine makes 400 N·m at 4000 RPM. ω = 4000 × π/30 = 418.9 rad/s, so P = 400 × 418.9 = 167 552 W = 167.6 kW (224.7 hp).
- Speed for a required torque. A conveyor needs 120 N·m from a 3 kW drive. n = 9549 × 3 / 120 = 238.7 RPM at the output shaft, so a 1450 RPM motor needs roughly a 6:1 reduction. Size it with the gear ratio calculator.
- The 5252 crossover. At 5252 RPM, 300 lb·ft gives 300 × 5252 / 5252 = 300 hp. Below 5252 RPM the torque number is larger; above it the horsepower number is larger.
Rated torque of common electric motors
Full-load torque from T = 9549 × P / n, using typical full-load speeds for 4-pole IEC (50 Hz) and NEMA (60 Hz) induction motors. Check your nameplate speed; slip changes it slightly (see the motor slip calculator).
| Rating | Speed (RPM) | Torque (N·m) | Torque (lb·ft) |
|---|---|---|---|
| 0.75 kW (1 hp) | 1420 / 1750 | 5.04 / 4.07 | 3.72 / 3.00 |
| 1.5 kW (2 hp) | 1430 / 1750 | 10.0 / 8.14 | 7.40 / 6.00 |
| 3 kW (4 hp) | 1435 / 1755 | 20.0 / 16.2 | 14.7 / 12.0 |
| 5.5 kW (7.5 hp) | 1450 / 1760 | 36.2 / 30.3 | 26.7 / 22.4 |
| 7.5 kW (10 hp) | 1450 / 1765 | 49.4 / 40.3 | 36.4 / 29.8 |
| 11 kW (15 hp) | 1460 / 1765 | 71.9 / 60.5 | 53.1 / 44.6 |
| 15 kW (20 hp) | 1465 / 1770 | 97.8 / 80.5 | 72.1 / 59.4 |
| 22 kW (30 hp) | 1470 / 1770 | 143 / 121 | 105 / 89.0 |
Values separated by a slash are 50 Hz IEC / 60 Hz NEMA. The hp figure in each row is the nearest NEMA size, so the 50 Hz and 60 Hz values are not exactly the same power.
Unit conversions used by the calculator
| Unit | In SI | Notes |
|---|---|---|
| 1 lb·ft | 1.355 818 N·m | Pound-force foot, the usual US torque unit |
| 1 lb·in | 0.112 985 N·m | 1/12 of a lb·ft; used for small motors and fasteners |
| 1 kgf·m | 9.806 65 N·m | Older European and Asian data sheets |
| 1 hp | 745.700 W | Mechanical (imperial) horsepower |
| 1 PS | 735.499 W | Metric horsepower (CV, ch, pk) |
| 1 RPM | 0.104 720 rad/s | π/30 exactly |
Common mistakes
- Using RPM where the formula needs rad/s. P = τ × ω only works with ω in rad/s. Plugging RPM straight in overstates power by a factor of 9.55.
- Mixing horsepower definitions. Mechanical hp (745.7 W) and metric PS (735.5 W) differ by 1.4%. Electrical hp (746 W) is close to mechanical but not identical.
- Treating torque output as constant across a gearbox. A reducer multiplies torque by its ratio but also loses 2–5% per stage to friction. The gear ratio calculator applies efficiency for you.
- Confusing input and output power on a motor. Nameplate kW is shaft output. Electrical input is higher by 1 / efficiency.
Frequently asked questions
How do I calculate torque from kW and RPM?
Torque in N·m = 9549 × power in kW ÷ speed in RPM. For example, 11 kW at 1460 RPM gives 9549 × 11 / 1460 = 71.9 N·m.
How do I convert torque and RPM to horsepower?
Horsepower = torque in lb·ft × RPM ÷ 5252. With N·m, use kW = N·m × RPM ÷ 9549, then divide kW by 0.7457 for hp.
Why do torque and horsepower curves cross at 5252 RPM?
Because hp = lb·ft × RPM / 5252. When RPM equals 5252 the two numbers are equal. It only happens when torque is in lb·ft and power in mechanical hp; in N·m and kW the curves cross at 9549 RPM.
Is power the same before and after a gearbox?
Ideally yes: a gearbox trades speed for torque at constant power. In practice each gear stage loses about 1–3% (spur and helical) and worm gears can lose 10–50%, so output power is input power times efficiency.
What does 9549 mean in the motor torque formula?
9549 is 60 000 / 2π. It combines the conversion from RPM to rad/s (×2π/60) with the conversion from watts to kilowatts (÷1000).
Can I use this calculator for engines?
Yes. Enter the dyno torque and the RPM where it was measured to get power at that point. Remember an engine's peak torque and peak power occur at different speeds.
Terms used on this page
- Torque (τ, T, M)
- Rotational force about an axis, in newton-metres (N·m) or pound-feet (lb·ft).
- Angular velocity (ω)
- Rotation rate in radians per second. ω = RPM × π/30.
- Shaft power (P)
- Mechanical power delivered by a rotating shaft, P = τ·ω, in watts or kilowatts.
- Horsepower (hp)
- Imperial power unit equal to 550 ft·lbf/s or 745.7 W.
- Metric horsepower (PS)
- 75 kgf·m/s, equal to 735.5 W; also written CV or ch.
- Full-load torque
- Torque a motor produces at rated power and rated speed.
Related calculators
- Gear Ratio & Pulley RPM CalculatorOutput RPM, torque and direction for gear trains and belt drives.
- SFM to RPM CalculatorSpindle RPM from cutting speed and diameter, plus feed rate.
- Linear ↔ Angular Velocity CalculatorConvert RPM and radius to m/s, km/h, mph and ft/min — and back.
- RPM to Hz CalculatorRPM, Hz, rad/s, °/s and period in one live converter.
- RPM ↔ rad/s converterω = n × π/30
- Motor slip calculatornₛ = 120·f / P