35 RPM to Radians Per Second Converter
Instant conversion for 35 RPM to rad/s (3.665191 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 3.6651914
- Degrees per Second (°/s)
- 210 °/s
- Hertz (Hz)
- 0.583333 Hz
- Revolutions per Second (RPS)
- 0.583333 rev/s
- Revolutions per Hour (RPH)
- 2,100 rev/hr
- Revolutions per Day
- 50,400 rev/day
- Radians per Minute (rad/min)
- 219.91149 rad/min
- Milliradians per Second (mrad/s)
- 3,665.1914 mrad/s
- Period (seconds per rev)
- 1.714286 s/rev
- Exact Formula
- 35 × π/30 = 3.6651914 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 35 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 35 × (π / 30) = 3.665191 rad/s
Exact fraction: 35π/30 rad/s · Reciprocal: 3.665 rad/s × (30/π) = 35 RPM
Reverse Conversion: 3.665 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
35 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
35 RPM = 7π/6 rad/s ≈ 3.665191 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 3.6645 rad/s instead of the exact 3.6652 rad/s — an error of 0.0006914 rad/s.
What this speed looks like in practice
At 35 RPM a shaft turns about 1.05× as fast as an LP record (33⅓ RPM). A 7-inch single (45 RPM) turns about 1.29× faster.
Revolutions over time
That is 2,100 revolutions per hour and 50,400 per day. A quarter turn (90°) takes 429 ms, and the shaft sweeps 0.21° every millisecond.
Rim speed and centripetal load at ω = 3.6652 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.03665 m/s · 0.1319 km/h | 0.1343 m/s² · 0.0137 g |
| 5 cm | 10 cm | 0.1833 m/s · 0.6597 km/h | 0.6717 m/s² · 0.06849 g |
| 10 cm | 20 cm | 0.3665 m/s · 1.319 km/h | 1.343 m/s² · 0.137 g |
| 25 cm | 50 cm | 0.9163 m/s · 3.299 km/h | 3.358 m/s² · 0.3425 g |
| 50 cm | 1 m | 1.833 m/s · 6.597 km/h | 6.717 m/s² · 0.6849 g |
| 1 m | 2 m | 3.665 m/s · 13.19 km/h | 13.43 m/s² · 1.37 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 35 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.5833 Hz | Below typical VFD range — use a gearbox |
| 4 | 1.167 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.75 Hz | Below typical VFD range — use a gearbox |
| 8 | 2.333 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 11.67 RPM · 1.222 rad/s | ×3 |
| 5:1 | 7 RPM · 0.733 rad/s | ×5 |
| 10:1 | 3.5 RPM · 0.3665 rad/s | ×10 |
| 30:1 | 1.167 RPM · 0.1222 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.006717 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.06717 J |
| 0.1 kg·m² (car flywheel) | 0.6717 J |
| 1 kg·m² (industrial flywheel) | 6.717 J |
Multiples of this speed
- 0.5× = 17.5 RPM1.8326 rad/s
- 2× = 70 RPM7.3304 rad/s
- 5× = 175 RPM18.326 rad/s
- 10× = 350 RPM36.6519 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 35 RPM to radians per second, multiply 35 by π and divide by 30: 35 × (π / 30) = 3.665191 rad/s (approx. 3.665 rad/s).
35 RPM equals 0.5833 Hz (revolutions per second), calculated by dividing 35 by 60 seconds.
To convert 3.665 rad/s back to RPM, multiply by 30 and divide by π: 3.665 × (30 / π) ≈ 35 RPM.
At 35 RPM, one full 360° revolution takes 1.7143 seconds (1714.29 ms).
A 4-pole induction motor has a synchronous speed of 35 RPM at 1.1667 Hz (f = RPM × poles / 120 = 35 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 3.665191 rad/s × 0.1 m = 0.3665 m/s (1.3195 km/h). The centripetal acceleration at the rim is ω²·r = 1.3434 m/s².