175 RPM to Radians Per Second Converter
Instant conversion for 175 RPM to rad/s (18.325957 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 18.325957
- Degrees per Second (°/s)
- 1,050 °/s
- Hertz (Hz)
- 2.916667 Hz
- Revolutions per Second (RPS)
- 2.916667 rev/s
- Revolutions per Hour (RPH)
- 10,500 rev/hr
- Revolutions per Day
- 252,000 rev/day
- Radians per Minute (rad/min)
- 1,099.5574 rad/min
- Milliradians per Second (mrad/s)
- 18,325.957 mrad/s
- Period (seconds per rev)
- 0.342857 s/rev
- Exact Formula
- 175 × π/30 = 18.325957 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 175 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 175 × (π / 30) = 18.325957 rad/s
Exact fraction: 175π/30 rad/s · Reciprocal: 18.326 rad/s × (30/π) = 175 RPM
Reverse Conversion: 18.326 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
175 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
175 RPM = 35π/6 rad/s ≈ 18.325957 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 18.3225 rad/s instead of the exact 18.326 rad/s — an error of 0.003457 rad/s.
What this speed looks like in practice
At 175 RPM a shaft turns about 3.89× as fast as a 7-inch single (45 RPM). A ceiling fan on high turns about 1.14× faster.
Revolutions over time
That is 10,500 revolutions per hour and 252,000 per day. A quarter turn (90°) takes 85.7 ms, and the shaft sweeps 1.05° every millisecond.
Rim speed and centripetal load at ω = 18.326 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.1833 m/s · 0.6597 km/h | 3.358 m/s² · 0.3425 g |
| 5 cm | 10 cm | 0.9163 m/s · 3.299 km/h | 16.79 m/s² · 1.712 g |
| 10 cm | 20 cm | 1.833 m/s · 6.597 km/h | 33.58 m/s² · 3.425 g |
| 25 cm | 50 cm | 4.581 m/s · 16.49 km/h | 83.96 m/s² · 8.562 g |
| 50 cm | 1 m | 9.163 m/s · 32.99 km/h | 167.9 m/s² · 17.12 g |
| 1 m | 2 m | 18.33 m/s · 65.97 km/h | 335.8 m/s² · 34.25 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 175 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 2.917 Hz | Below typical VFD range — use a gearbox |
| 4 | 5.833 Hz | Reachable with a VFD |
| 6 | 8.75 Hz | Reachable with a VFD |
| 8 | 11.67 Hz | Reachable with a VFD |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 58.33 RPM · 6.109 rad/s | ×3 |
| 5:1 | 35 RPM · 3.665 rad/s | ×5 |
| 10:1 | 17.5 RPM · 1.833 rad/s | ×10 |
| 30:1 | 5.833 RPM · 0.6109 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.1679 J |
| 0.01 kg·m² (bench-grinder wheel) | 1.679 J |
| 0.1 kg·m² (car flywheel) | 16.79 J |
| 1 kg·m² (industrial flywheel) | 167.9 J |
Multiples of this speed
- 0.5× = 87.5 RPM9.163 rad/s
- 2× = 350 RPM36.6519 rad/s
- 5× = 875 RPM91.6298 rad/s
- 10× = 1,750 RPM183.2596 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 175 RPM to radians per second, multiply 175 by π and divide by 30: 175 × (π / 30) = 18.325957 rad/s (approx. 18.326 rad/s).
175 RPM equals 2.9167 Hz (revolutions per second), calculated by dividing 175 by 60 seconds.
To convert 18.326 rad/s back to RPM, multiply by 30 and divide by π: 18.326 × (30 / π) ≈ 175 RPM.
At 175 RPM, one full 360° revolution takes 0.3429 seconds (342.86 ms).
A 4-pole induction motor has a synchronous speed of 175 RPM at 5.8333 Hz (f = RPM × poles / 120 = 175 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 18.325957 rad/s × 0.1 m = 1.8326 m/s (6.5973 km/h). The centripetal acceleration at the rim is ω²·r = 33.5841 m/s².