45 RPM to Radians Per Second Converter
Instant conversion for 45 RPM to rad/s (4.712389 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 4.712389
- Degrees per Second (°/s)
- 270 °/s
- Hertz (Hz)
- 0.75 Hz
- Revolutions per Second (RPS)
- 0.75 rev/s
- Revolutions per Hour (RPH)
- 2,700 rev/hr
- Revolutions per Day
- 64,800 rev/day
- Radians per Minute (rad/min)
- 282.74334 rad/min
- Milliradians per Second (mrad/s)
- 4,712.389 mrad/s
- Period (seconds per rev)
- 1.333333 s/rev
- Exact Formula
- 45 × π/30 = 4.712389 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 45 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 45 × (π / 30) = 4.712389 rad/s
Exact fraction: 45π/30 rad/s · Reciprocal: 4.712 rad/s × (30/π) = 45 RPM
Reverse Conversion: 4.712 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
45 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
45 RPM = 3π/2 rad/s ≈ 4.712389 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 4.7115 rad/s instead of the exact 4.7124 rad/s — an error of 0.000889 rad/s.
What this speed looks like in practice
That is the typical speed of a 7-inch single (45 RPM). At 45 RPM a shaft turns about 1.35× as fast as an LP record (33⅓ RPM). A ceiling fan on high turns about 4.44× faster.
Revolutions over time
That is 2,700 revolutions per hour and 64,800 per day. A quarter turn (90°) takes 333 ms, and the shaft sweeps 0.27° every millisecond.
Rim speed and centripetal load at ω = 4.7124 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.04712 m/s · 0.1696 km/h | 0.2221 m/s² · 0.02264 g |
| 5 cm | 10 cm | 0.2356 m/s · 0.8482 km/h | 1.11 m/s² · 0.1132 g |
| 10 cm | 20 cm | 0.4712 m/s · 1.696 km/h | 2.221 m/s² · 0.2264 g |
| 25 cm | 50 cm | 1.178 m/s · 4.241 km/h | 5.552 m/s² · 0.5661 g |
| 50 cm | 1 m | 2.356 m/s · 8.482 km/h | 11.1 m/s² · 1.132 g |
| 1 m | 2 m | 4.712 m/s · 16.96 km/h | 22.21 m/s² · 2.264 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 45 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.75 Hz | Below typical VFD range — use a gearbox |
| 4 | 1.5 Hz | Below typical VFD range — use a gearbox |
| 6 | 2.25 Hz | Below typical VFD range — use a gearbox |
| 8 | 3 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 15 RPM · 1.571 rad/s | ×3 |
| 5:1 | 9 RPM · 0.9425 rad/s | ×5 |
| 10:1 | 4.5 RPM · 0.4712 rad/s | ×10 |
| 30:1 | 1.5 RPM · 0.1571 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.0111 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.111 J |
| 0.1 kg·m² (car flywheel) | 1.11 J |
| 1 kg·m² (industrial flywheel) | 11.1 J |
Multiples of this speed
- 0.5× = 22.5 RPM2.3562 rad/s
- 2× = 90 RPM9.4248 rad/s
- 5× = 225 RPM23.5619 rad/s
- 10× = 450 RPM47.1239 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 45 RPM to radians per second, multiply 45 by π and divide by 30: 45 × (π / 30) = 4.712389 rad/s (approx. 4.712 rad/s).
45 RPM equals 0.7500 Hz (revolutions per second), calculated by dividing 45 by 60 seconds.
To convert 4.712 rad/s back to RPM, multiply by 30 and divide by π: 4.712 × (30 / π) ≈ 45 RPM.
At 45 RPM, one full 360° revolution takes 1.3333 seconds (1333.33 ms).
A 4-pole induction motor has a synchronous speed of 45 RPM at 1.5 Hz (f = RPM × poles / 120 = 45 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 4.712389 rad/s × 0.1 m = 0.4712 m/s (1.6965 km/h). The centripetal acceleration at the rim is ω²·r = 2.2207 m/s².