Rotational Motion Formulas: rad/s, v = ωr and a = ω²r
Rotational motion formulas explained: radians, rad/s, angular acceleration, tangential speed v = ωr, centripetal acceleration and RCF with worked examples.
You have a wheel turning at 830 RPM, an exam question asking for the speed of its rim, and a formula sheet full of Greek letters. You plug the RPM straight into v = ωr and get an answer that is wrong by a factor of almost ten. Every student meets this trap, and most meet it twice. We fix it here with one unit rule, six formulas, and five worked examples you can check line by line.
The radian and its dimensionless status
All rotational motion formulas start from the angle. An angle in radians is the arc length s divided by the radius r, so one radian is the angle at which the arc equals the radius. A full turn has an arc of 2πr, which gives 2π radians per revolution, or about 6.2832 rad.
θ = s / r
Because θ is a length divided by a length, the units cancel. The BIPM SI Brochure classes the radian as a coherent derived unit equal to the number one, which is the formal reason it can appear or vanish in a calculation. That vanishing act is convenient. It is also the source of most lost marks.
Degrees carry no such property. A degree is 1/360 of a turn, an arbitrary historical division, and it does not equal arc length over radius. Put degrees into θ = s/r and the answer is off by a factor of 57.296. The verdict is simple: every formula in this guide assumes radians.
Angular velocity in every common unit
Angular velocity ω is the rate of change of angle, ω = Δθ/Δt. In SI it is measured in radians per second. Engineers on the shop floor quote RPM, electrical engineers quote hertz, and animation or gyroscope datasheets quote degrees per second.
ω (rad/s) = RPM × 2π / 60
The factor 2π/60 equals 0.10472. Memorise it, or keep the RPM to radians per second converter open in another tab while you study. The table below gives the exact factors between the four units, so you can move between any two in a single step.
| From → To | rad/s | RPM | Hz (rev/s) | °/s |
|---|---|---|---|---|
| 1 rad/s | 1 | 9.5493 | 0.15915 | 57.296 |
| 1 RPM | 0.10472 | 1 | 0.016667 | 6 |
| 1 Hz | 6.2832 | 60 | 1 | 360 |
| 1 °/s | 0.017453 | 0.16667 | 0.0027778 | 1 |
A full treatment of ω, including vector direction and the right-hand rule, sits in our angular velocity guide. For this article we need only its magnitude. One colloquial note: if you see "rad/s" and "s⁻¹" used interchangeably in a textbook, the author is fine, because the radian is dimensionless.
Period and frequency
The period T is the time for one complete revolution. Frequency f is its reciprocal, counted in revolutions per second, or hertz. Both connect to ω through the 2π radians in one turn.
ω = 2πf = 2π / T
A shaft at 3,000 RPM turns 50 times per second, so f = 50 Hz and T = 20 ms. Its angular velocity is 2π × 50 = 314.16 rad/s. Notice the overlap with the 50 Hz mains supply, which is no accident: a two-pole synchronous machine on a 50 Hz grid runs at exactly 3,000 RPM, a link we develop in the electric motor speed guide.
Angular acceleration α
Angular acceleration α is the rate at which ω changes, α = Δω/Δt, measured in rad/s². A positive α means the rotation speeds up in the chosen direction and a negative α means it slows down. A spinning object with constant ω has α = 0, even though every point on it still accelerates toward the centre.
That last fact confuses many learners on first contact. Angular acceleration describes changes in spin rate, while centripetal acceleration describes the constant change in direction of each point's velocity. Keep the two quantities in separate boxes and the rest of this guide stays tidy.
What causes α is torque, through τ = Iα, where I is the moment of inertia. The link between torque, speed and the power a motor delivers is covered in our torque, power and speed guide. Here we treat α as given and ask what follows from it.
The rotational kinematic equations
For constant angular acceleration, rotational motion obeys four equations that mirror the linear SUVAT set exactly. Swap displacement s for θ, velocity u and v for ω₀ and ω, and acceleration a for α. The derivations are identical because the calculus is identical: integrate α once to get ω, integrate again to get θ.
| Linear form | Rotational form | Missing variable |
|---|---|---|
| v = u + at | ω = ω₀ + αt | θ |
| s = ut + ½at² | θ = ω₀t + ½αt² | ω |
| v² = u² + 2as | ω² = ω₀² + 2αθ | t |
| s = ½(u + v)t | θ = ½(ω₀ + ω)t | α |
ω = ω₀ + αt | θ = ω₀t + ½αt² | ω² = ω₀² + 2αθ
To derive the third equation, take t = (ω − ω₀)/α from the first equation and substitute it into the fourth. The product (ω + ω₀)(ω − ω₀) collapses to ω² − ω₀², and dividing by 2α leaves θ. You can rebuild the whole table from two definitions in under a minute, which beats memorising it under exam pressure.
Worked example: a motor spinning up
A motor starts from rest and reaches 3,000 RPM in 2.0 s at constant acceleration. Convert first: 3,000 × 0.10472 = 314.16 rad/s. Then α = (314.16 − 0)/2.0 = 157.08 rad/s².
The angle turned is θ = ½ × 157.08 × 2.0² = 314.16 rad. Divide by 2π and the shaft completes exactly 50 revolutions during the spin-up. As a check, ω² = 2αθ gives 2 × 157.08 × 314.16 = 98,696, and 314.16² is also 98,696.
Tangential speed v = ωr
Every point on a rigid rotating body shares the same ω, yet points farther from the axis travel farther per turn. The arc length relation s = rθ, differentiated with respect to time at constant r, gives the tangential speed directly. The derivation takes one line.
v = ωr
The result holds only with ω in rad/s and r in metres, giving v in m/s. Because the radian is dimensionless, rad × m/s becomes plain m/s with no hidden factor. Feed RPM into the same formula and the answer comes out 9.549 times too large, the most common error in introductory mechanics.
Use the calculator below to test your own values. For a deeper look at unit traps such as diameter versus radius, read the RPM to linear velocity guide.
RPM to Linear Velocity Calculator
Translate shaft rotational speed and wheel/roller dimensions into real-world linear speed.
Machinists use the same relation under a different name. Cutting speed in surface feet per minute is v = ωr expressed in imperial units, which is why the SFM to RPM guide reads like this section with inches and feet. The physics never changes between the classroom and the lathe.
The tangential acceleration follows the same pattern. Differentiate v = ωr once more and you get aₜ = αr, the rate at which the rim speeds up along its path. It is zero whenever the spin rate is steady.
Centripetal acceleration a = ω²r = v²/r
A point moving in a circle at constant speed still accelerates, because the direction of its velocity rotates with it. Over a small time dt the velocity vector turns through an angle ω dt, so its change has magnitude v × ω dt, pointing toward the centre. Dividing by dt gives a = vω, and substituting v = ωr produces the two standard forms.
a꜀ = ω²r = v² / r
The quadratic dependence on ω carries the whole engineering story. Double the RPM and the centripetal acceleration quadruples, along with the stress in the rotor and the load on the bearings. A useful analogy for this scaling is a car's kinetic energy: going from 50 to 100 km/h feels like one step on the pedal, yet the energy to absorb in a crash rises fourfold, and a spinning rotor punishes extra RPM in exactly the same way.
Pick the form that matches your data. Use ω²r when you know the rotation rate and v²/r when you know the rim speed. Both give the same number when the inputs are consistent, which makes each a free check on the other.
Relative centrifugal force (RCF)
In laboratory work, centripetal acceleration is expressed as a multiple of standard gravity, g = 9.80665 m/s². That ratio is the relative centrifugal force, written as "× g". Substituting ω = 2π × RPM/60 into a = ω²r and dividing by g gives the practical formula, with r in centimetres.
RCF = 1.118 × 10⁻⁵ × r (cm) × RPM²
The constant 1.118 × 10⁻⁵ comes from (2π/60)² ÷ 9.80665 × 0.01, which evaluates to 1.1182 × 10⁻⁵. Protocols specify RCF because two centrifuges with different rotor radii produce different g-forces at the same RPM. Our centrifuge RPM to RCF guide walks through rotor-specific conversions and the minimum, average and maximum radius question.
Worked examples from real machines
Numbers carry the argument here, so each example runs the full chain from RPM or speed to ω, v and a. Every result below has been checked both ways where two routes exist. If your own working lands within rounding of these figures, your method is sound.
Car wheel at motorway speed
A car travels at 100 km/h on tyres with a rolling radius of 0.32 m. The road speed is 100 ÷ 3.6 = 27.78 m/s, and for rolling without slipping that equals the rim speed relative to the axle. Rearranging v = ωr gives ω = 27.78 ÷ 0.32 = 86.8 rad/s, or about 829 RPM.
The centripetal acceleration of the tread is ω²r = 86.8² × 0.32 ≈ 2,411 m/s². The route v²/r gives 27.78² ÷ 0.32 ≈ 2,411 m/s², which confirms it. The tread pulls about 246 g, so a stone caught in it flies off with real force.
Laboratory centrifuge
A rotor with a 10 cm radius spins at 4,000 RPM. The RCF formula gives 1.118 × 10⁻⁵ × 10 × 4,000² = 1,789 × g. Working from first principles, ω = 418.88 rad/s, so ω²r = 418.88² × 0.10 ≈ 17,546 m/s², and dividing by 9.80665 gives 1,789 × g again.
The rim speed is v = 418.88 × 0.10 ≈ 41.9 m/s, roughly 151 km/h. Raising the speed to 8,000 RPM would push the RCF to about 7,155 × g, four times higher because RCF scales with the square of RPM.
Hard drive platter
A desktop hard drive spins at 7,200 RPM. Then ω = 7,200 × 0.10472 = 753.98 rad/s, f = 120 Hz, and the period is T = 1/120 s ≈ 8.33 ms. On average the head waits half a turn for the target sector, so the average rotational latency is about 4.17 ms.
A 3.5-inch drive uses platters about 95 mm across, so the outer edge sits near r = 0.0475 m. The edge speed is 753.98 × 0.0475 ≈ 35.8 m/s, close to 129 km/h, while the head flies nanometres above that surface. Treat the platter radius as approximate, since exact dimensions vary by model.
Washing machine spin cycle
A washing machine drum of radius 0.25 m spins at 1,400 RPM. The angular velocity is 1,400 × 0.10472 ≈ 146.6 rad/s, so the drum wall moves at v = 146.6 × 0.25 ≈ 36.7 m/s. The RCF is 1.118 × 10⁻⁵ × 25 × 1,400² ≈ 548 × g.
Water leaves the fabric because the drum holes provide no inward force on it, so each droplet continues along a tangent. At 548 × g the clothes press against the wall far harder than any wringing by hand. The drum radius is an assumed typical figure, so check your own machine's specifications before quoting it.
Earth's rotation
Earth turns once per sidereal day of about 86,164 s, so ω = 2π ÷ 86,164 ≈ 7.292 × 10⁻⁵ rad/s. At the equator, with r ≈ 6.378 × 10⁶ m, the surface speed is v ≈ 465 m/s, faster than a passenger jet. The centripetal acceleration is ω²r ≈ 0.0339 m/s².
That figure is about 0.35 % of g. You weigh very slightly less at the equator because a small share of gravity supplies the centripetal force, and Earth's oblate shape adds a further effect on top. A planet-sized rotation with a tiny ω still produces a large speed, because r is enormous.
| Example | ω (rad/s) | r (m) | v (m/s) | a꜀ (m/s²) | RCF (× g) |
|---|---|---|---|---|---|
| Car wheel, 100 km/h | 86.8 | 0.32 | 27.8 | 2,411 | 246 |
| Centrifuge, 4,000 RPM | 418.9 | 0.10 | 41.9 | 17,546 | 1,789 |
| Hard drive, 7,200 RPM | 754.0 | 0.0475 | 35.8 | 27,003 | 2,754 |
| Washer, 1,400 RPM | 146.6 | 0.25 | 36.7 | 5,373 | 548 |
| Earth, equator | 7.292 × 10⁻⁵ | 6.378 × 10⁶ | 465 | 0.0339 | 0.0035 |
The same method extends to propellers, where tip speed approaches the speed of sound and limits the usable RPM. Our drone propeller tip speed calculator applies v = ωr to blade tips and compares the result with Mach 1.
Common student mistakes
The errors below appear year after year in coursework and exams. Each has a simple test you can apply before handing in an answer. Run through the list on every rotational problem until the checks become habit.
Degrees in formulas. Using θ in degrees in s = rθ or the kinematic equations inflates the result by 57.3. Convert with θ(rad) = θ(°) × π/180 before you substitute anything.
RPM in v = ωr. RPM counts revolutions per minute, two unit changes away from rad/s. The result comes out 9.549 times too large, and in a = ω²r the error squares to about 91 times.
Diameter for radius. Wheel and disc sizes are quoted as diameters. Halve the figure first, or your speed doubles and your centripetal acceleration doubles with it.
Mixing α and a꜀. A rotor at steady speed has zero angular acceleration and large centripetal acceleration. When a problem says "constant RPM", set α = 0 and keep a꜀.
Centimetres in the SI form. The RCF shortcut uses r in centimetres, while a = ω²r needs metres. Mixing the two forms gives answers off by a factor of 100.
The question that remains is: how do you know your final number is plausible? Compare it with the worked table above. A bench centrifuge reaching 50 × g or a car tyre tread at 25,000 × g would signal a slipped unit somewhere.
A compact sheet of rotational motion formulas
Every result in this guide follows from three definitions: θ = s/r, ω = dθ/dt and α = dω/dt. The rest is substitution and one line of calculus each time. Keep this sheet beside your notes and rebuild any line you forget.
| Quantity | Formula | SI unit |
|---|---|---|
| Angular displacement | θ = s / r | rad |
| Angular velocity | ω = Δθ / Δt = 2πf = 2π / T | rad/s |
| RPM conversion | ω = RPM × π / 30 | rad/s |
| Angular acceleration | α = Δω / Δt | rad/s² |
| Tangential speed | v = ωr | m/s |
| Tangential acceleration | aₜ = αr | m/s² |
| Centripetal acceleration | a꜀ = ω²r = v² / r | m/s² |
| Relative centrifugal force | RCF = 1.118 × 10⁻⁵ × r(cm) × RPM² | × g |
For extended derivations and practice sets, the free OpenStax University Physics Volume 1 chapter on fixed-axis rotation is excellent. The lecture notes in MIT OpenCourseWare 8.01 Classical Mechanics cover the same ground with vector calculus. For unit conventions, the NIST guide to SI units settles any dispute about symbols and prefixes.
Frequently Asked Questions
What are the main rotational motion formulas?
The core set is θ = s/r, ω = Δθ/Δt, α = Δω/Δt, the kinematic equations ω = ω₀ + αt, θ = ω₀t + ½αt² and ω² = ω₀² + 2αθ, plus v = ωr and a꜀ = ω²r. All of them require angles in radians and ω in rad/s.
Why is the radian considered dimensionless?
A radian is arc length divided by radius, metres over metres, so the units cancel to the number one. The SI treats it as a derived unit equal to one, which is why rad·m/s simplifies to m/s in v = ωr.
How do I convert RPM to rad/s?
Multiply RPM by 2π/60, which equals 0.10472. For example, 1,800 RPM × 0.10472 = 188.5 rad/s. To go back, multiply rad/s by 9.5493.
What is the difference between centripetal and tangential acceleration?
Centripetal acceleration, ω²r, points toward the axis and exists whenever the object rotates. Tangential acceleration, αr, points along the path and exists only when the spin rate changes. At constant RPM the tangential part is zero.
How is RCF calculated from RPM?
Use RCF = 1.118 × 10⁻⁵ × r × RPM², with r in centimetres measured from the axis to the sample. A 10 cm rotor at 4,000 RPM gives about 1,789 × g.
Does Earth's rotation affect my weight?
Yes, by a small amount. At the equator, Earth's rotation produces a centripetal acceleration of about 0.034 m/s², roughly 0.35 % of g, so your measured weight is a little lower there than at the poles.
Ready to run the numbers?
Get your result instantly — private, in your browser.