RPM to Radians Per SecondRPM to rad/s
Metrology & Kinematics Quick Reference Cheatsheet

Rotational Velocity & Motor Speeds Reference Chart

Standard induction motor synchronous speeds, full-load slip estimations, and exact SI angular velocities (BIPM / NIST / DIN 1301)

Key Analytical Conversion Formulas

RPM to Angular Velocity (rad/s):ω = RPM × (π / 30)
Angular Velocity to RPM:RPM = ω × (30 / π)
Tangential Linear Speed (m/s):v = ω · r
Centripetal Acceleration (m/s²):a_c = ω² · r = v² / r

1. 60 Hz Grid Motor Speeds (NEMA Standard — US / Canada / Latin America)

Calculated for 3-phase induction motors with typical 2.5%–3% full-load slip.

PolesSynchronous RPMFull-Load RPMSync Angular Speed (rad/s)Full-Load rad/sShaft Rotation (Hz)
2 Poles3,600 RPM3,450 RPM120π ≈ 376.991115π ≈ 361.28360 Hz
4 Poles1,800 RPM1,750 RPM60π ≈ 188.49658.33π ≈ 183.26030 Hz
6 Poles1,200 RPM1,150 RPM40π ≈ 125.66438.33π ≈ 120.42820 Hz
8 Poles900 RPM850 RPM30π ≈ 94.24828.33π ≈ 89.01215 Hz
10 Poles720 RPM680 RPM24π ≈ 75.39822.67π ≈ 71.20912 Hz
12 Poles600 RPM560 RPM20π ≈ 62.83218.67π ≈ 58.64310 Hz

2. 50 Hz Grid Motor Speeds (IEC / DIN Standard — Europe / Asia / Africa)

Calculated for standard industrial motors operating on European and international 50 Hz AC supply networks.

PolesSynchronous RPMFull-Load RPMSync Angular Speed (rad/s)Full-Load rad/sShaft Rotation (Hz)
2 Poles3,000 RPM2,850 RPM100π ≈ 314.15995π ≈ 298.45150 Hz
4 Poles1,500 RPM1,450 RPM50π ≈ 157.08048.33π ≈ 151.84425 Hz
6 Poles1,000 RPM950 RPM33.33π ≈ 104.72031.67π ≈ 99.48416.67 Hz
8 Poles750 RPM700 RPM25π ≈ 78.54023.33π ≈ 73.30412.5 Hz
10 Poles600 RPM560 RPM20π ≈ 62.83218.67π ≈ 58.64310 Hz
12 Poles500 RPM460 RPM16.67π ≈ 52.36015.33π ≈ 48.1718.33 Hz
Academic Benchmark Note: In college physics homework (Halliday & Resnick, Serway & Jewett), the frequently assigned problem value of 5.36 rad/s converts to exactly 51.18423 RPM (reciprocal calculation: 5.36 × 30/π). See the full textbook solution in our 5.36 rad/s guide. Have a nameplate speed below these sync values? Work out the exact slip with the motor slip calculator.

How to use this chart

Reading the tables

Each row is one pole count. The synchronous column is the speed of the stator's rotating magnetic field — the theoretical maximum an induction motor approaches with no load. The full-load column is a typical nameplate speed once the motor is doing work. Both are given in RPM and as exact multiples of π rad/s, which is the form you should carry through torque, power and kinematics calculations.

The last column is the shaft's rotation rate in revolutions per second (Hz). It is not the grid frequency: a 4-pole motor on a 60 Hz supply turns 30 times per second.

Synchronous speed

n_s = 120 × f / P ω_s = 4π × f / P (rad/s)

Synchronous speed depends only on supply frequency f and the number of poles P. Example: a 4-pole motor on 60 Hz gives 120 × 60 / 4 = 1,800 RPM, which is exactly 60π ≈ 188.50 rad/s. The same motor on a 50 Hz grid runs at 1,500 RPM (50π rad/s).

Because P is always even, only a fixed ladder of speeds exists on a fixed-frequency supply — which is why 3,600, 1,800, 1,200 and 900 RPM (60 Hz) or 3,000, 1,500, 1,000 and 750 RPM (50 Hz) appear everywhere.

Slip: why the nameplate speed is lower

slip s = (n_s − n) / n_s × 100 %

An induction motor needs its rotor to lag the rotating field to induce current and produce torque. That lag is slip. A 4-pole 60 Hz motor rated 1,750 RPM has s = (1,800 − 1,750) / 1,800 ≈ 2.8 %. Nameplates in the 1,725–1,780 RPM range are all 4-pole motors; higher-efficiency designs usually have less slip.

The full-load figures in the tables assume typical slip of about 2.5–8 % depending on size. Always use the nameplate speed for real calculations.

Changing speed with a VFD

n = 120 × f_VFD / P

A variable-frequency drive changes f, so speed scales proportionally: a 4-pole motor driven at 45 Hz has a synchronous speed of 1,350 RPM (45π rad/s). Below roughly 5–10 Hz self-cooled motors lose cooling and torque stability; above base frequency the motor enters constant-power (field-weakening) operation, so available torque falls.

Why engineers work in rad/s

Power, torque and speed are linked by P = τ × ω, and kinetic energy by E = ½ I ω². Both equations only work with ω in radians per second. Plugging RPM in directly gives answers that are off by a factor of 30/π ≈ 9.55.

Motor speed FAQs

Why does my 1,800 RPM motor say 1,750 or 1,725 RPM on the nameplate?
1,800 RPM is the synchronous speed of a 4-pole motor on 60 Hz. The nameplate shows the full-load speed after slip. A motor marked 1,725–1,780 RPM is still a 4-pole, "1,800 RPM class" motor, and the two are interchangeable for most applications.
How do I get the same motor speed in Europe (50 Hz) as in the US (60 Hz)?
On 50 Hz a motor runs at 5/6 of its 60 Hz speed (1,800 → 1,500 RPM). To match the 60 Hz speed, either drive it from a VFD at 60 Hz (checking the motor's voltage and thermal rating), change the pulley or gear ratio by 6:5, or choose a motor with a different pole count.
How many poles does a 1,450 RPM motor have?
Find the nearest synchronous speed above the nameplate value: 1,450 RPM sits just under 1,500 RPM, so it is a 4-pole motor on a 50 Hz supply with about 3.3 % slip.
Is the RPM on a motor nameplate the synchronous speed?
No. Induction motor nameplates list the full-load speed, which is below synchronous speed. Only synchronous motors (and stepper or servo motors under control) run exactly at the calculated field speed.