2,500 RPM to Radians Per Second Converter
Instant conversion for 2,500 RPM to rad/s (261.799388 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 261.79939
- Degrees per Second (°/s)
- 15,000 °/s
- Hertz (Hz)
- 41.666667 Hz
- Revolutions per Second (RPS)
- 41.666667 rev/s
- Revolutions per Hour (RPH)
- 150,000 rev/hr
- Revolutions per Day
- 3,600,000 rev/day
- Radians per Minute (rad/min)
- 15,707.963 rad/min
- Milliradians per Second (mrad/s)
- 261,799.39 mrad/s
- Period (seconds per rev)
- 0.024 s/rev
- Exact Formula
- 2500 × π/30 = 261.79939 rad/s
- Nearest Real-World Example
- Car engine — highway (2,500 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 2,500 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 2500 × (π / 30) = 261.799388 rad/s
Exact fraction: 2500π/30 rad/s · Reciprocal: 261.8 rad/s × (30/π) = 2,500 RPM
Reverse Conversion: 261.8 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
2,500 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
2,500 RPM = 250π/3 rad/s ≈ 261.799388 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 261.75 rad/s instead of the exact 261.7994 rad/s — an error of 0.04939 rad/s.
What this speed looks like in practice
At 2,500 RPM a shaft turns about 1.39× as fast as a 4-pole motor on a 60 Hz grid. A laptop hard drive (5,400 RPM) turns about 2.16× faster.
Revolutions over time
That is 150,000 revolutions per hour and 3,600,000 per day. A quarter turn (90°) takes 6 ms, and the shaft sweeps 15° every millisecond.
Rim speed and centripetal load at ω = 261.7994 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 2.618 m/s · 9.425 km/h | 685.4 m/s² · 69.89 g |
| 5 cm | 10 cm | 13.09 m/s · 47.12 km/h | 3,427 m/s² · 349.5 g |
| 10 cm | 20 cm | 26.18 m/s · 94.25 km/h | 6,854 m/s² · 698.9 g |
| 25 cm | 50 cm | 65.45 m/s · 235.6 km/h | 17,130 m/s² · 1,747 g |
| 50 cm | 1 m | 130.9 m/s · 471.2 km/h | 34,270 m/s² · 3,495 g |
| 1 m | 2 m | 261.8 m/s · 942.5 km/h | 68,540 m/s² · 6,989 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 2,500 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 41.67 Hz | Reachable with a VFD |
| 4 | 83.33 Hz | Reachable with a VFD |
| 6 | 125 Hz | Above typical VFD range |
| 8 | 166.7 Hz | Above typical VFD range |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 833.3 RPM · 87.27 rad/s | ×3 |
| 5:1 | 500 RPM · 52.36 rad/s | ×5 |
| 10:1 | 250 RPM · 26.18 rad/s | ×10 |
| 30:1 | 83.33 RPM · 8.727 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 34.27 J |
| 0.01 kg·m² (bench-grinder wheel) | 342.7 J |
| 0.1 kg·m² (car flywheel) | 3.427 kJ |
| 1 kg·m² (industrial flywheel) | 34.27 kJ |
Multiples of this speed
- 0.5× = 1,250 RPM130.8997 rad/s
- 2× = 5,000 RPM523.5988 rad/s
- 5× = 12,500 RPM1,308.9969 rad/s
- 10× = 25,000 RPM2,617.9939 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 2,500 RPM to radians per second, multiply 2500 by π and divide by 30: 2500 × (π / 30) = 261.799388 rad/s (approx. 261.8 rad/s).
2,500 RPM equals 41.6667 Hz (revolutions per second), calculated by dividing 2500 by 60 seconds.
To convert 261.8 rad/s back to RPM, multiply by 30 and divide by π: 261.8 × (30 / π) ≈ 2,500 RPM.
At 2,500 RPM, one full 360° revolution takes 0.024 seconds (24.00 ms).
A 4-pole induction motor has a synchronous speed of 2,500 RPM at 83.3333 Hz (f = RPM × poles / 120 = 2500 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 261.799388 rad/s × 0.1 m = 26.1799 m/s (94.2478 km/h). The centripetal acceleration at the rim is ω²·r = 6853.8919 m/s².