10 RPM to Radians Per Second Converter
Instant conversion for 10 RPM to rad/s (1.047198 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 1.0471976
- Degrees per Second (°/s)
- 60 °/s
- Hertz (Hz)
- 0.166667 Hz
- Revolutions per Second (RPS)
- 0.166667 rev/s
- Revolutions per Hour (RPH)
- 600 rev/hr
- Revolutions per Day
- 14,400 rev/day
- Radians per Minute (rad/min)
- 62.831853 rad/min
- Milliradians per Second (mrad/s)
- 1,047.1976 mrad/s
- Period (seconds per rev)
- 6 s/rev
- Exact Formula
- 10 × π/30 = 1.0471976 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 10 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 10 × (π / 30) = 1.047198 rad/s
Exact fraction: 10π/30 rad/s · Reciprocal: 1.047 rad/s × (30/π) = 10 RPM
Reverse Conversion: 1.047 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
10 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
10 RPM = π/3 rad/s ≈ 1.047198 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 1.047 rad/s instead of the exact 1.0472 rad/s — an error of 0.0001976 rad/s.
What this speed looks like in practice
At 10 RPM a shaft turns about 10× as fast as a clock's second hand. A utility-scale wind turbine rotor turns about 1.5× faster.
Revolutions over time
That is 600 revolutions per hour and 14,400 per day. A quarter turn (90°) takes 1.5 s, and the shaft sweeps 0.06° every millisecond.
Rim speed and centripetal load at ω = 1.0472 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.01047 m/s · 0.0377 km/h | 0.01097 m/s² · 0.001118 g |
| 5 cm | 10 cm | 0.05236 m/s · 0.1885 km/h | 0.05483 m/s² · 0.005591 g |
| 10 cm | 20 cm | 0.1047 m/s · 0.377 km/h | 0.1097 m/s² · 0.01118 g |
| 25 cm | 50 cm | 0.2618 m/s · 0.9425 km/h | 0.2742 m/s² · 0.02796 g |
| 50 cm | 1 m | 0.5236 m/s · 1.885 km/h | 0.5483 m/s² · 0.05591 g |
| 1 m | 2 m | 1.047 m/s · 3.77 km/h | 1.097 m/s² · 0.1118 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 10 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.1667 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.3333 Hz | Below typical VFD range — use a gearbox |
| 6 | 0.5 Hz | Below typical VFD range — use a gearbox |
| 8 | 0.6667 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 3.333 RPM · 0.3491 rad/s | ×3 |
| 5:1 | 2 RPM · 0.2094 rad/s | ×5 |
| 10:1 | 1 RPM · 0.1047 rad/s | ×10 |
| 30:1 | 0.3333 RPM · 0.03491 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.0005483 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.005483 J |
| 0.1 kg·m² (car flywheel) | 0.05483 J |
| 1 kg·m² (industrial flywheel) | 0.5483 J |
Multiples of this speed

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 10 RPM to radians per second, multiply 10 by π and divide by 30: 10 × (π / 30) = 1.047198 rad/s (approx. 1.047 rad/s).
10 RPM equals 0.1667 Hz (revolutions per second), calculated by dividing 10 by 60 seconds.
To convert 1.047 rad/s back to RPM, multiply by 30 and divide by π: 1.047 × (30 / π) ≈ 10 RPM.
At 10 RPM, one full 360° revolution takes 6 seconds (6000.00 ms).
A 4-pole induction motor has a synchronous speed of 10 RPM at 0.3333 Hz (f = RPM × poles / 120 = 10 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 1.047198 rad/s × 0.1 m = 0.1047 m/s (0.377 km/h). The centripetal acceleration at the rim is ω²·r = 0.1097 m/s².